Shenzhen CREP Optoelectronics Co. Ltd

Home > Company News > Content
LED Panel Lights Cost-effective
- Jul 21, 2017 -

Led panel lights as a new light source - led as the light source of indoor lighting, in the design highlights the beautiful simple design concept, the atmosphere of luxury momentum, with the beauty of people's eyes, unique design, through the light guide plate through The light, enough uniformity, soft light and bright and comfortable. In the role of lighting under the lighting, but also shadow the possession of a major loss, the general light will be caused by radiation, LED Panel Light and led panel after a special means of improvement, this concern is no longer exist. Led panel lights use is also very wide, the following Xiaobian to a brief introduction.

Led panel light from the border and the bottom plate, light guide plate and diffuser plate, lamp beads and patch, aluminum plate, power lamp basic components, the emergence of LED to break the traditional light source design methods and ideas, Led panel light through the light guide plate through Of the light, enough uniformity, soft light and bright and comfortable. Led panel lamp use is also very wide, LED Panel Light has been replaced by the trend of the grille, the following small series to a brief introduction.

LED panel light is a high-end indoor lighting, LED Panel Light the outer frame by the anodized aluminum alloy, the light source for the LED, the entire design simple and beautiful lighting, atmospheric luxury, both good lighting effects, but also bring people The feeling of beauty. LED panel lights unique design, light through the high light transmittance of the light guide plate after the formation of a uniform flat light effect, illumination uniformity, light soft, LED Panel Light comfortable and yet bright, can effectively alleviate eye fatigue. LED panel lights can also prevent radiation, will not stimulate pregnant women, the elderly, children's skin.

_led panel light accessories

1. Panel light aluminum frame:

Is the main channel of LED cooling, the appearance of simple and generous, you can use ZY0907, the use of mold stamping die low cost, processing costs are low; die-cast aluminum frame IP level can be higher, the surface texture is good, the overall appearance, but the early put mold costs Higher.

2.LED light source:

Usually LED lamp beads use 3528, it was also used 3014 and 5050.3014 and 5050 low cost, light effect slightly worse, the key is its light guide network design difficulties. LED Panel Light 3528 luminous efficiency of high network point of good versatility.

3.LED light guide plate:

The side of the LED light through the network refraction of the light from the front evenly derived, light guide plate is the key to LED panel light quality control. Network design is not good, see the overall light effect is very poor, the general will appear on both sides of the dark side of the dark, or there is light into the light band, or visible local dark area, or there are different angles of brightness inconsistencies.

4.LED Diffusion Board:

The light guide plate light evenly derived, but also play a fuzzy dot role. Diffuse plate generally use the acrylic 2.0 sheet or PC material, almost the PS material, the lower the cost of acrylic and light transmission than the PC slightly higher, acrylic brittle anti-aging performance is weak, LED Panel Light PC price is slightly more expensive, but anti-aging performance Strong.

5. Reflective paper:

The light guide plate on the back of the remaining light reflected to improve the luminous efficiency, usually RW250.

6. Rear cover:

The main role is to seal the LED panel lights, generally with 1060 aluminum, LED Panel Light but also play a little heat dissipation.

7. Drive power:

There are two kinds of LED drive power, one is the use of constant current power supply, this mode is high efficiency, PF value of up to 0.95, cost-effective; second is the use of constant pressure with constant current power supply, stable performance, but low efficiency,

8. Install the pendant:

Hanging wire, mounting bracket, etc. for the installation of fixed accessories.

LED panel lights are widely used, has replaced the trend of the grid lights; LED panel lights are mainly used in: 1, the ceiling (instead of the original grid lights); 2, walls (not only as lighting purposes, but also with artistic expression); 3, the installation of the body (the pursuit of practical and artistic combination, easy to install); 4, other (also available in other places, such as train cars or large mobile cars, counters, etc.);

LED panel lights due to soft light, beautiful appearance, LED Panel Light has been widely favored by European and American merchants, a large number of foreign investors are buying good quality, good service, good price of panel lights products and suppliers; it seems only a simple lighting, but because of Its high market positioning determines the customer's quality requirements for this product is extremely harsh, coupled with the product itself involves materials, optics, structure, hardware, electronics and other fields, the general company does not have a complete development team and sufficient development Experience and follow-up of the supply chain management capabilities, it is difficult to really successful development, coupled with the understanding of the market requirements are not clear, so a lot of development costs cast in exchange for only a customer does not recognize the product.